EarthQuaker DevicesAvalanche Run V2 Delay + Reverb Pedal
- No Hassle
Earthquaker Avalanche Run V2 Delay + Reverb Pedal
The Avalance Run has now been upgraded with a revised proprietary DSP algorithm that enables updated stereo imaging, and a brand new custom enclosure!
The EarthQuaker Devices Avalanche Run parallels their Dispatch Master pedal, with some stunning additions. Avalanche Run boasts a powerful DSP program capable of emulating classic reverb and delay effects. The pedal’s front panel interface is remarkably straightforward, featuring dedicated controls for its Time, Repeats, Tone, Decay, Ratio, and Mix parameters alongside three separate modes: Normal, Reverse, and Swell. All this plus the capacity for self-oscillation and optimal expression control via the pedal’s corresponding input renders the Avalanche Run as one of the most effective reverb pedals on the market.
Avalanche Run v2 Features
- Stereo Reverb and Delay with Tap Tempo
- Proprietary DSP algorithm for lush reverb and delay
- Stereo inputs and outputs
- Up to 2 seconds of delay time
- Updated reverb algorithm for improved stereo imaging
- New custom-built enclosure
- 24-bit 96kHz A/D and D/A converters
- 115dB signal-to-noise ratio
- True bypass
- Silent relay-based switching
- All-analog dry signal path
- All-digital wet signal path with 20 Hz - 20kHz frequency response
- Lifetime guarantee
- Current draw: 425mA
- Weight: 18 ounces
- Product Dimensions: 4.65″ x 4.15″ x 2.25″
- Each and every Avalanche Run is completely assembled, wired and tested by total human beans in the tiny tundra town of Akron, Ohio.
Get ready to dance as she shows us how she blends live instrumentation with sampling, singing, and tight beats for stunning performances!
Time: This controls the delay time and goes from 0ms to just under 2000ms.
Repeats: Controls the regeneration of the delay, from zero repeats to near infinite.
Tone: Controls the tone for the delay line only. Roll off highs to the left, roll off lows to the right and get a flat response in the middle.
Mix: The is the volume control for the delay line. This blends in the wet with dry until 1 o’clock, 1 o’clock to 3 o’clock boosts the wet signal over the dry and 3 o’clock up brings down dry until it is fully wet when all the way up.
Expression Jack Assign Switch: Use this switch to map the expression jack to one of the assigned controls.
Decay: Controls the reverb decay length
R Mix: Controls the reverb mix
Time: This takes over for the delay time control and is DRASTICALLY different than the interface control. Using the expression pedal to control the time will give you all kinds of wild effects that can not be achieved by turning the knob.
Repeats: Controls the delay repeats
D Mix: Controls the delay mix
Toggle: This takes over for the toggle switch and will cross fade from forward delay in heel down position to reverse delay in toe down position.
Ratio Selector Switch: Selects delay subdivisions when time is set by the “Tap” switch.
1/1: Quarter Note
3/4: Dotted 8th
2/3: Quarter Note Triplet
1/2: 8th Note
1/3: 8th Note Triplet
1/4: 16th Note
Decay: Controls the decay length of the reverb, short decay counterclockwise, long cavernous decay clockwise.
Toggle Switch (Mode Selector)
Normal: This is the “standard” delay and reverb mode
Reverse: This is reverse delay mode with “standard” reverb
Swell: This is the volume swell mode
Mix: This is the volume control for the reverb. Blends in the wet with dry until 1 O’clock, 1 O’clock to 3 O’clock boosts the wet signal over the dry and 3 O’clock up brings down dry until it is fully wet when all the way up.